Without a doubt about setting up an Aftermarket Stereo into a Dodge Neon
The OEM mind device within my ’04 Dodge Neon went finally went kaput after many years of adequate solution, and after numerous lonely months on the highway with out a track to sing-along/butcher, I made the decision it had been time for you to place some severe work into changing it. This is basically the very first time i have changed a car or truck stereo, but discovered it was quite simple so long as you understand what components you want. This informative article will not be ideal for a seasoned vehicle sound specialist, however it will help away some DIY’ers on a tight budget.
Acquiring the parts that are necessary
You will most likely need to buy the necessary adapters unless you intend to replace your current OEM unit with another OEM unit. An antenna adapter, and a wiring harness which will allow you to connect your new head unit correctly without snipping off the OEM connector in particular, you will need a dash kit which will allow you to install an aftermarket head unit into the proprietary receptacle. Provided I went with the cheapest equipment I could find, which upon arrival seemed nonetheless well-made and entirely serviceable that I am not too particular about quality on this matter. For the convenience, here is the things I purchased:
Once more, mostly because i will be low priced, we went by having a double XR4115 In-Dash Digital Media Receiver as my mind brand new product. We do not utilize CDs or tapes, therefore AM/FM radio with the integral mp3 capability came across my requirements completely. We originally wanted an even more name that is recognizable, but individuals with the features i desired had been away from my cost range, therefore rather i came across a respectable deal on a gently utilized Dual. I really hope it is built sufficiently to complete the job for the couple of years.
Additionally, you will a Phillips screwdriver, a dozen approximately 18-22 Gauge Butt Splices , and a couple of pliers.
Getting rid of the old product
First rung on the ladder would be to take away the old device. When it comes to security of your self along with your opportunities, you are able to disconnect the negative black that is( t erminal on your own automobile battery pack.
Take away the air ports from your own dash panel. This is carried out by straightening them, gripping securely, and pulling right down. Underneath are a couple of screws that really must be applied for.
Eliminate most of the AC/heating settings by gripping them securely and pulling them away. There is no need to be concerned about the career; they could just return in a single method.
Now grip the dash panel close to the top and away pry it. It really is loosely guaranteed with springtime videos which will cave in with a little bit of force. After the top comes down, you will see it is nevertheless linked in the bottom; this is certainly is certainly not a hinge, but more springtime videos, therefore try to swing don’t the dash panel down. Rather, pull the underside directly away.
Keep in mind that the air is connected to the dash with four screws. Just just simply Take these out and also the old mind device should slip down easily. It is important to disconnect the header and antenna. Pull the antenna out firmly. The connector includes a latch on the underside that may ensure it is eliminated
Planning the head unit that is new
Old head unit, in comparison to the mounted unit that is new
The kit that is mounting with four elements; a panel, a bezel, and two brackets. The brackets are marked “left” and “right,” the panel is marked towards the top. The brackets snap to the panel with synthetic videos, dealing with inwards to guide the [radio].
We first installed the brand new mind product in to the mount. It just went in through the front. It had been a decent fit, and discovered that I’d to carry the brackets in place to help keep them from bending way too much and possibly breaking the videos. The screws failed to hold it securely set up, nonetheless it is very effective sufficient to keep this head that is particular from sliding down or bouncing around. You could need to utilize washers, or various screws than those provided when you look at the package.
The essential time part that is consuming of task is wiring the harnesses. Within my instance, both the wiring harness that was included with my stereo while the aftermarket wiring harness for my vehicle had been color-coded to your exact same standard, so that the process ended up being since straightforward as joining like cable to like cable. Insert the conclusion of a cable into one region of the butt connector, crimp it utilizing the pliers, insert the matching then wire and crimp it, too.
There clearly was one “gotcha” to understand, though. The Neon harness we received is sold with two black colored cables and two yellowish; nonetheless, in the event that you go through the header when you look at the vehicle it self, you will notice that this has wiring just for certainly one of each. Which means one cable shall be real time, one other a dud. Therefore, when you’re wiring your harnesses together, be sure you link the right people. The correct wires are those closer to the plastic clip as you can see in the picture to the right, for my car. I experienced to know about this the difficult means, which is the reason why a few of my other pictures reveal wrong wiring.
Last installation
When you’ve got the radio in its mount therefore the harnesses prepared, the remainder is a piece of cake. We connected the harness and antenna adapters towards the vehicle and brand new mind device, I quickly reconnected my automobile battery pack to be able to test the machine.
As soon as I saw it was working, I utilized some zip ties to help keep the cables neat, and stuffed every thing in to the dash. We placed the brand new radio and installed the four screws in the corners.
With this point, completing the installation is probably reversing the actions you took to eliminate the dash panel in the first place. Snap the panel on bottom-first, install the screws underneath the atmosphere ports, back snap the vents in, and place the AC/heating control knobs right straight right right back on.
